Fundamental Plumber Tips for Bathtub Installation
Fundamental Plumber Tips for Bathtub Installation
Blog Article
What're your beliefs on Tools You Need to Install a New Bathtub ?
Installing a tub isn't exactly rocket science, however it does call for strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably hard task. If the old bathtub is readily available, the job can move easily; if you need to open up a wall surface to eliminate the old tub and position the brand-new tub, the job is a lot harder. In either situation, the job is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub and embeded in the new one. Make sure you have actually qualified on your own for the task and fit trying it. Rather than working with a specialist to take over a halfway-completed task, it is better to take into consideration employing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This article will aid you install a new bath tub in your restroom if you have actually currently bought a new bathtub and also don't need to transform the arrangement of your previous supply of water pipelines.
Your devices and also product list should comprise the following:
Planning for the Installation
First of all, the sustaining framework supplied with the bath ought to be fitted (if required) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to prevent pressure on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be fitted in its final setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you ought to do is detach the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the limited accessibility that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipes. As soon as the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before going on to fit the new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bath tub
Making use of the two wooden boards under its feet, put the tub in the called for placement. The wood boards are useful in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The following goal is to guarantee that the tub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the bath tub till the spirit level reads degree.
To mount taps, fit the bottom of the outermost versatile tap connector to the ideal supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the water supply and inspect all joints and new pipework for leakages and tighten them if essential. Fill the tub as well as also inspect the overflow outlet and also the normal outlet for leakages.
Ultimately, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bath tub needs to wait up until the bathtub has been utilized at the very least when as this will certainly resolve it into its final setting.
Fitting New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in location between the faucet and also the sink. Protect the tap in position with the producer provided backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap adapters. The former kind should be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the fitting can move enough to split an inflexible seal, causing the water to permeate the wall surface in between the bathroom as well as the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can break fairly very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also conveniently available on the marketplace. It is recommended to fit the floor tiles making use of waterproof or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
I ran across that page about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when perusing the web. Sharing is caring. Helping people is fun. Thanks for your time. Come back soon.
Best choice? Ring us! Report this page